A Step-by-Step Overview to Setting Up a Bathtub
A Step-by-Step Overview to Setting Up a Bathtub
Blog Article
They are making several great observations on How to Install a Bathtub Yourself in general in this post further down.
Setting up a bathtub isn't exactly rocket science, but it does call for strong plumbing, woodworking, as well as in some cases, tiling skills. Changing an old tub with a new one is also a moderately hard task. If the old tub is readily accessible, the task can move quickly; if you have to open up a wall to remove the old tub as well as position the brand-new bathtub, the job is much harder. In either case, the task is within a house handyman's abilities, although you will require an assistant to leave the old bathtub and also set in the brand-new one. Make sure you have actually certified yourself for the job and also fit trying it. Rather than hiring a service provider to take control of a halfway-completed job, it is better to consider using one prior to you begin. Chances are you might need a professional plumber to make tube links.
This post will help you mount a new bathtub in your washroom if you have actually currently gotten a new tub and also do not need to change the arrangement of your previous water pipelines.
Your tools and product list ought to comprise the following:
Removing Old Taps
If you need to change old taps with brand-new ones as a part of your setup, then the first thing you should do is separate the water. After doing so, activate the taps to drain any water remaining in the system. The process of removing the existing taps can be fairly troublesome because of the restricted accessibility that is usually the situation.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the faucets. Have a towel prepared for the remaining water that will certainly come from the pipes. As soon as the supply pipes have been gotten rid of, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from transforming during this process. As soon as the faucets have been removed, the holes in the bath/basin will certainly have to be cleaned of any type of old sealing compound.
Prior to proceeding to fit the brand-new faucets, compare the pipe links on the old taps to the new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the brand-new taps to fit.
Suitable New Taps
If the tails of the new faucets are plastic, then you will need a plastic connector to stop damage to the thread. One end of the adapter fits on the plastic tail of the tap and also the various other end provides a link to the existing supply pipes.
If you require to fit a monobloc, then you will certainly need lowering couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next off, position the faucet in the mounting opening in the bath/basin guaranteeing that the washing machines are in area between the faucet as well as the sink. Secure the faucet in place with the maker provided backnut. When the tap is safely in position, the supply pipes can be linked to the tails of the taps. The taps can either be attached by using corrugated copper piping or with regular tap adapters. The former kind should be linked to the faucet ends initially, tightening just by hand. The supply pipelines can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Setting up the Bath tub
Using both wood boards under its feet, place the tub in the required setting. The wood boards are helpful in uniformly spreading out the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto 4 little factors.
The next goal is to make certain that the bathtub is leveled all round. This can be accomplished by examining the spirit level as well as readjusting the feet on the bath tub until the level reviews level.
To install faucets, fit all-time low of the outermost flexible tap adapter to the appropriate supply pipe by making a compression join; after that do the very same for the other tap.
Turn on the water and check all joints as well as brand-new pipework for leakages and also tighten them if necessary. Fill up the tub and likewise inspect the overflow electrical outlet and also the normal outlet for leaks.
Lastly, take care of the bathroom paneling as defined in the manufacturer's instruction manual. Tiling as well as sealing around the tub must wait till the bath tub has actually been made use of at least once as this will settle it into its final position.
Preparing for the Setup
Firstly, the supporting frame supplied with the bath should be fitted (if required) according to the producer's instructions. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is very important to make certain that if the faucet includes a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is also reasonable to fit a sustaining plate under the faucets device to avoid stress on the tub.
Fit the versatile tap connectors to the bottom of both faucets making use of 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Ensure you use every one of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom ought to currently be ready to be suited its final setting.
Tiling Around the Bath tub
In the area where the bathroom meets the ceramic tile, it is necessary to seal the accompanies a silicone rubber caulking. This is important as the installation can relocate enough to split a rigid seal, triggering the water to pass through the wall between the bathroom and the tiling, causing difficulties with dampness and possible leakages to the ceiling listed below.
You can choose from a range of coloured sealers to blend in your fixtures and also installations. They are sold in tubes as well as cartridges, and also are capable of sealing spaces approximately a width of 3mm (1/8 inch). If you have a larger space to load, you can fill it with twists of soaked newspaper or soft rope. Bear in mind to constantly fill the tub with water prior to securing, to permit the movement experienced when the tub is in usage. The sealer can crack fairly early if you do not take into consideration this activity prior to sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are also quickly offered on the marketplace. It is suggested to fit the tiles using water-resistant or waterproof sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We had been shown that editorial about How to Install a Bathtub Yourself from a good friend on a different web address. Sharing is caring. You never know, you might be doing someone a favor. Thank you so much for your time spent reading it.
Suggested Site
Report this page